Introduction
Purpose of this document
This document provides essential information on the installation and configuration of YSoft USB Card Reader version 3.
Validity of this document
This document applies to YSoft USB Card Reader v3.
Goals and objectives
That YSoft USB Card Reader v3 can be connected simply to a multi-functional device and serve for user authentication using a card. The card must be assigned to a user in the Dispatcher Paragon system. After successful authentication, the user can work the with device and perform their print, copy, or scan jobs (depending on the device).
YSoft USB Card Reader v3 can also be connected to workstations and used with a credit charger application or with the Dispatcher Paragon client for authentication.
Terms and abbreviations
- MFD - Multi-Functional Device
- USB Card Reader v3 - YSoft USB Card Reader version 3
Prerequisite knowledge
The person installing USB Card Reader v3 must meet the following requirements:
- knowledge of the Dispatcher Paragon system (installation/administration/attendance)
Disclaimer
A user that makes changes or modifications not expressly approved by the party responsible for compliance (Konica Minolta, Inc.) could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at their own expense.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
สำ หรับลูกค้ำที่ซื้อผลิตภัณฑ์นีี ขอบคุณท่ ท่านกรุณาเลือกซื้อผลิตภัณฑ์น้ ก่อนการใชผ ลิตภัณฑ์ โปรดอ่านขอ มูลและคา แนะนา ต่อไปน้ อย่างถ่ ถว นเพื่อการใชงานอย่างปลอดภัย ข อบังคับ เครื่อง โทรคมนาคมและอุปกรณ์น้ ม ความสอดคลอ งตามขอ กา หนดของ กทช.
埋込み型心臓ペースメーカーおよび埋込み型除細動器を装着されている場合は、本装置または本装置のワイ ヤレスカードシステムのリーダライタ部（アンテナ部）から12cm以上離れて携行および使用してください。 電波により埋込み型心臓ペースメーカーおよび埋込み型除細動器の動作に影響を与える場合があります。
The product conforms with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 27, 2003 on waste electrical and electronic equipment (WEEE) and Directive 2003/108/EC of the European Parliament and of the Council of December 8, 2003 amending Directive 2002/96/EC on waste electrical and electronic equipment (WEEE).
Only for indoor use
Overview
System overview
Dispatcher Paragon® USB Card Reader has the following characteristics:
- Connection and power supply of the card reader are via the USB host interface
- Exchange of the card reader is possible without turning off the MFD (hot-plug)
- Compatibility with some MFD additions
Hardware components
USB card reader specifications
Parameter | Value |
|---|---|
Identification | Using a card reader |
Voltage | 5 V DC |
Maximum current input | 0.5 A |
Working temperature | +5°C to +35°C |
Storage temperature | 0°C to +50°C |
Working air humidity | 20% to 85% without condensation |
Storage air humidity | 8% to 85% without condensation |
Resistance to magnetic field | no added resistance |
Transmitting frequency | 125 kHz, 132 kHz, 134.2 kHz, 13.56 MHz, 2.4 GHz |
Usage
Please use the card by placing it on the edge of the reader as indicated below.
LED indicator
LED color | meaning |
|---|---|
LED off | The USB device has not been initialized yet or the device is in sleep mode. |
Orange | Initializing |
Green | Card reader initialized. Ready to read a card. |
White | Card read OK |
Red | Card read error or card refused |
Blue | Programming card processing |
Yellow | Firmware update |
Mounting instructions
Please mount the card reader to an MFD using the mounting kit.
Keep unprotected cords out of the path of foot traffic to prevent tripping. Do not leave cords dangling anywhere where they can be pulled down and tripped over.
Configuration
For configuration, see USB Reader tool for Reader configuration.
Risk Description | Control Measures | Risk Analysis | Additional Measures to be carried out) | ||
O | P | Risk Rating | |||
Falling of object/component | A mounting kit is supplied with the device. | Small | Possible | L (C4) | Correct mounting is indicated in the manual. |
Tripping over a cable | The cable is fitted with a connector at both ends that can be disconnected. | Serious | Possible | M (C3) | A recommendation on cable placement is indicated in the manual. |
Entry of water into electronic components | The device is damaged. | Small | Possible | L (C4) | The manual states the user is to prevent water from entering the device. |
Exposure to non-ionizing radiation (radiofrequency) | The device produces radiofrequency radiation below limits indicated by relevant norms. | Small | Improb. | L (D4) | The norms the device meets are listed in the manual: EN 55032:15 EN 55024:10 ETSI EN 301489-3 V1.6.1:13 ETSI EN 301489-1 V1.9.2:11 ETSI EN 301489-1 V2.2.0:17 ETSI EN 301489-3 V2.1.1:17 ETSI EN 300330-2 V1.6.1:15 ETSI EN 300330-1 V1.8.1:15 ETSI EN 300330 V2.1.1:17 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 EN 62368-1:2014/AC:2015 |