Dispatcher Paragon

The YSoft SafeQ Terminal UltraLight contains status LEDs that serve for interaction with the user. This chapter describes the beeps the terminal emits and LED codes it displays to notify the user about various status conditions.

Beep code sequences

In the following table, a period ( . ) represents a short beep and a dash ( - ) represents a long beep.

This option is available only if the sound is enabled.

Sequence	Description
-	Card read error. Place the card again or use a different card.
. -	Terminal validation failed. Server reports that the terminal is not registered on Dispatcher Paragon.
- -	No print job is waiting in queue.
. . -	User quota has been exceeded or user has no billing code assigned.
- . -	User authentication failed. The PIN is not valid or the ID card is not registered in Dispatcher Paragon. If Dispatcher Paragon Payment System is used, it can indicate account is disabled.
. - -	The terminal received an error or warning message from the Dispatcher Paragon server. If Dispatcher Paragon Payment System is used, it can indicate insufficient credit balance for current user (according Dispatcher Paragon system settings for Dispatcher Paragon Payment System – pricePerPageReservationStrategyForCopyOnHwTerminal ) to perform copies/scans.
- - -	Connection to Dispatcher Paragon server failed.
. . . -	Hardware configuration is corrupt and the terminal cannot continue booting.
- .. -	Maximum number of firmware update attempts reached but no valid firmware detected.
. - . -	Firmware update failed.
- - . -	Software configuration cannot be saved. Probably faulty terminal EEPROM.
. . - -	Software configuration is damaged and the terminal is loading defaults.
- . - -	Maximum number of firmware update attempts reached and the terminal is resuming normal boot.
. - - -	Firmware damaged.
- - - -	Network initiation failed.
. . . .	Keyboard PCB failure.
- . . .	No reader is connected. Reader is required for operation.
. - . .	Firmware update failed. Error in server response. Dispatcher Paragon server is probably not configured correctly.
- - . .	Firmware update failed. Cannot connect to Dispatcher Paragon server.

LED code sequences

The following table shows the various LED code sequences and explains what they indicate.

There are following colors used for icons:

Green - Led is green
Red - Led is red
Orange - Led is orange
Grey - Led is off

Sequence	Description
	*Animated* Unsuccessful authentication. The terminal does not recognize the card, PIN, or Card Activation Code code.
	*All LEDs are off* Terminal power is off.
	Animated Terminal is processing; please wait.
	Animated Firmware upgrade in progress; please wait.
	Firmware upgrade in progress; please wait.
	Swipe card or enter PIN.
	Enter PIN (when authentication requires card + PIN).
	Enter Card Activation Code (when Card Activation Codes are enabled on the Dispatcher Paragon server).
	Print jobs are available and copying is possible. Press the Print or Copy icon. NOTE: This code appears only on YSoft SafeQ Terminal UltraLight Print & Copy.
	No print jobs are available in the queue. Copying is possible. Press the Copy icon. NOTE: This code appears only on YSoft SafeQ Terminal UltraLight Print & Copy.
	*Flashing* Copying in progress. To cancel, press X or OK, or place a card. NOTE: This code appears only on YSoft SafeQ Terminal UltraLight Print & Copy.
	*Flashing* Copying in progress. Server issued a warning. See the MFD display panel for details. NOTE: This code appears only on YSoft SafeQ Terminal UltraLight Print & Copy.
	*Flashing* Printing in progress. Please wait until the print job is finished.
	*Flashing* Printing in progress. Server issued a warning. See the MFD display panel for details.
	*Flashing* An error occurred. See beep codes for details (page).
	Sequential... Sequence that appears as a user enters a PIN.
	Terminal has not been fully configured. Please contact Konica Minolta Customer support services.
	*During boot* WARNING: Do not perform this action unless instructed to do so by Konica Minolta. Enter the terminal model. For UltraLight Print & Copy, press 1. For UltraLight Print Only, press 3.
	*During initialization beep sequence* Indicates UltraLight Print & Copy model.
	*During initialization beep sequence* Indicates UltraLight Print Only model.
	*During initialization beep sequence* Indicates Ethernet Reader model.